Home / Products /

EasyMax V2

Glucose Meters and Strips

EasyMax V2
EasyMax V2

EasyMax V2

The EPS EasyMax V2 is an automatic blood glucose meter. The accuracy of its blood glucose measurement technology has yet to be proven to MDR requirements. Blood glucose measurements are taken from the finger. It is intended for self-measurement and home use.

Features

  • Under-fill blood volume detection
  • Bilingual Voice MeterEnglish & Spanish
  • LED-lit Strip slot Indicator
  • Before-meal/After-meal/ Control solution marking

‍

Specifications

Instructions

FAQs

Testing Videos

Data Transfer: Mini USB Port

Batteries: 2 x Alkaline 1.5V (AAA)

Standards:

  • IVD 98/79/EC
  • ISO 13485 : 2003
  • ISO 14971 : 2009
  • ISO 15197 : 2013
  • EN 980 : 2008
  • EN 61326-1 : 2006
  • EN 61326-2-6 : 2005
  • EN 61010-2-101 : 2002

Temp & Humidity:

  • Operating : 10℃~40℃, below 85% R.H.
  • Meter storage : -10℃~65℃, below 90% R.H.
  • Strip storage : 2℃~30℃, below 90% R.H.
  • Transportation : 2℃~30℃, below 90% R.H.

Accuracy:

  • 95% within + 15 mg/dL when glucose <100mg/dL
  • 95% within + 15% when glucose >100mg/dL

Precision: CV (correlation variation) is less than 5%

Error-Codes:

  • Err : humidified / Used strips
  • LP : Low power, please replace new battery
  • 001 with err icon : Not enough blood
  • 005 with err icon : system fault
  • HI : test result is higher than 630 mg/dL
  • LO: test result is lower than 20 mg/dL
  • Ht : Temperature too high to have a test
  • Lt : Temperature too low to have a test

Capacity: 480 results (glucose level, date & time)

Blood Specimen: Capillary whole blood / Venous whole blood

Sample Volume: 0.6 ul

Testing Time: 5 Seconds

Hematocrit range: 30-55%

Alternate Site Testing: Fingertip, Palm, Forearm

Measuring Range: 20 - 600 mg/dL

Meter Dimension: 83.7 x 51.2 x 22.9 mm

Weight: 44.6 g (without battery)

Battery Life: Over 1,000 times

Auto Shut-Off: Power off functions after 90 sec no key pressed

Time Setting: 12 Hours or 24 Hours (Optional)

Principles: Electrochemical biosensor technology

‍

How do I set the time and date?

How do I run a control solution test?

How do I Insert a Lancet into the Lancing Device?

How do I do a blood test?

How do I check the readings stored in memory?

‍

General Meter Accuracy

Factors That Affect Accuracy
Solutions
Test strip problems
Throw out damaged or outdated test strips. Store strips in their sealed container; keep them away from heat, direct sunlight, moisture and humidity. Be sure the strips are meant for your specific glucose meter.
Extreme temperatures
Keep your glucose meter and test strips at room temperature or at the recommended temperatures as stated in your manual.
Alcohol, dirt or other substances on your skin
Wash your hands and the testing site with warm soap and water before pricking your skin.
Monitor problems
Fully insert the test strip into the monitor. Replace the monitor batteries as needed.
Not enough blood applied to the test strip
Apply a generous drop of blood to the test strip or the amount recommended in the meter manual. EasyMax only require 0.6µL.
Testing site location
If you're using a site other than your fingertip and you think the reading is wrong, test again using blood from a fingertip. Blood samples from alternate sites aren't as accurate as fingertip samples  when your blood sugar level is rising or falling quickly.

Other Factors that affect accuracy:

  • A dirty meter.
  • If test strips are not compatible with the meter you're using, results may be inaccurate or no result will be obtained.  If the wrong strip is used, it may not even fit into the slot or it may fit, but the meter won’t turn on.
  • Substances left on your hands. For example, if there is a sugary substance on the finger used for lancing, even if it’s a small amount that can’t be seen, a high blood glucose reading can result.
  • Wet fingers.  Fluid mixes with blood and can cause an inaccurate reading.

How to Avoid an Inaccurate Blood Glucose Reading

  • Before using the meter for the first time and then again every few weeks, check your meter using the control solution.  Control solution is only good for three months once opened.  Label the control solution bottle with the date you open it.  Check the date and shake control solution before using.  The value the control solution gives should be in the target range printed on the strips container.
  • Make sure strips are not expired.  EasyMax test strip vials once opened need to be discarded 90 days after date first opened.
  • Select site on one side of the center of a fingertip.  Rotate sites for each check.
  • Apply gentle pressure to lanced finger to help the drop of blood form on the surface.
  • Completely fill the strip target area with blood.

EasyMax® Control Solution Test

EasyMax® Blood Test